Nature's Generator 350W Wind Turbine
📦 Order now, receive it between
Choose options
The Nature's Generator 350W Wind Turbine provides a renewable wind-charging option for compatible Nature's Generator power systems. It is designed to complement solar and AC charging, allowing compatible systems to capture wind energy when sunlight is limited.
The turbine is rated to produce up to 350 watts at approximately 27 mph wind speeds and can operate at wind speeds up to 110 mph. It includes the turbine, three blades, hub and nose cone, controller box, 100-foot wind turbine cable, and installation hardware.
Key Features
- 350W rated power at approximately 27 mph wind speed
- Designed for compatible Nature's Generator Powerhouse and MyGrid systems
- 3-phase permanent magnet synchronous system
- 63-inch (1.6 m) rotor diameter
- Fiberglass nylon composite turbine blades
- Cast aluminum alloy body with powder coating
- Stainless steel flange for mounting
- 100-foot wind turbine cable included
- Weatherproof M19 3P cable connectors
- Anderson wind-input connectors
- Over-voltage, over-current, and reverse-charging protection
- Resettable fuse
- CE and RoHS certifications
Wind Charging Performance
The turbine is rated for 350 watts at approximately 27 mph. Actual power generation depends on wind speed and site conditions. Nature's Generator states that the turbine can operate at wind speeds up to 110 mph.
Because wind conditions vary, actual energy production will depend on the location, wind speed, installation height, surrounding terrain, and other environmental factors. The turbine should be installed where adequate and consistent wind conditions are available.
Compatible Nature's Generator Systems
The 350W Wind Turbine is designed for Nature's Generator systems that support the higher wind-power input.
- MyGrid 10K Gen 1 — Compatible
- MyGrid 10K Gen 2 — Compatible
- Powerhouse 7200 Gen 1 — Compatible
- Powerhouse 7200 Gen 2 — Compatible
This 350W turbine is not the appropriate wind turbine for the Nature's Generator Standard 1800, Lithium 1800, Elite, or Lithium 3600 systems. Those models use the compatible 150W wind turbine.
Durable Outdoor Construction
The turbine uses a cast aluminum alloy body with powder coating and fiberglass nylon composite blades. Its stainless steel flange provides a corrosion-resistant mounting interface for outdoor installations.
The included wind turbine cable uses 12 AWG pure copper conductors and is supplied with weatherproof M19 3P connectors.
Technical Specifications
| Specification | Details |
|---|---|
| Rated Power | 350W at approximately 27 mph |
| Maximum Wind Speed | 110 mph |
| Rotor Diameter | 63 in / 1.6 m |
| System Type | 3-Phase Permanent Magnet Synchronous System |
| Blade Material | Fiberglass Nylon Composite |
| Turbine Body | Cast Aluminum Alloy with Powder Coating |
| Wind Turbine Cable | 12 AWG Pure Copper |
| Cable Length | 100 ft |
| Wind Cable Connector | Weatherproof M19 3P Connector |
| Wind Input Connector | Anderson Connector |
| Mounting Compatibility | 1.5-inch Schedule 40 pipe or tower |
| Turbine Weight | 37 lbs / 17 kg |
| Certifications | CE, RoHS |
Mounting Requirements
The turbine is designed to mount on a nominal 1.5-inch Schedule 40 steel tube or pipe, with an outside diameter of approximately 1.875 to 1.900 inches.
The mounting pole or tower is not included. Nature's Generator specifically recommends using steel tubing or piping for the tower and states that plastic pipe should not be used. The tower must be appropriately designed to support the turbine and withstand the expected wind loads.
What's Included
- 1 × Nature's Generator 350W Wind Turbine
- 1 × Hub Nose Cone
- 3 × Wind Turbine Blades
- 1 × 100 ft Wind Turbine Cable
- 1 × Controller Box
- 1 × Hardware and Tool Bag
- 1 × User Guide
Mounting pole/tower is not included.
Wind Charging for Backup and Off-Grid Systems
The 350W Wind Turbine can add another renewable charging source to compatible Nature's Generator systems. When suitable wind conditions are available, the turbine can complement solar charging and provide an additional charging option during periods when solar production is limited.
Actual energy production varies according to wind conditions and installation location. The turbine should be used with a compatible Nature's Generator system and installed according to the manufacturer's instructions.
Important Information
- This product is a wind turbine charging accessory and does not include a Nature's Generator power station.
- Mounting pole or tower is not included.
- Some assembly is required.
- Use only with compatible Nature's Generator systems.
- Actual power generation depends on wind speed and environmental conditions.
- Follow the manufacturer's installation instructions and applicable local requirements.